http://www.fobsun.com     sales@fobsun.com

Fobsun

User's manual for Linear LED Wall Washers-IP65

This manual includes important information about checking after receiving the product, cautions, working environment of the product, user's responsibilities and operation instructions, please read it carefully before you use the product.

Product Checking

1) Unpack and carefully examine the product.
2) Report any damage and save all packing material if any part is damaged during the transportation.
3) Do not attempt to use this device if it is damaged.

Cautions

1) This device shall be installed and operated by a qualified electrician or technician in accordance with all relevant local codes.
2) Risk of electric shock. Ensure that the power supply is off when wiring or soldering the sections of the device.
3) Do not use sharp tools near or on the surface of the device.
4) DO not plug them into power when the product is still in package.
5) Don't use anything to cover the fixture during application.
6) Make sure the ground wire connected well to avoid electric shock due to metal housing.
7) Don't use this product in close environment.
8) If this product appears to be damaged, do not attempt any repair, please contact your dealer.

Working Environment

This product is suitable for indoor and outdoor use, and applicable for both dry and damp environments.

User Responsibilities

It is the responsibility of the contractor, installer, purchaser, owner, and user to install, maintain, and operate the device in such a manner as to comply with all state and local laws, ordinances, and regulations.
Note: The instructions and precautions set forth in this user guide are not necessarily all-inclusive, all conceivable, or relevant to all applications, FOBSUN Electronics cannot anticipate all conceivable or unique situations.

Operation Instructions

Control Mode

Independent mode: choose the effects that you need by buttons on the back of the device.
Auto online DMX mode: International standard DMX512 signal control. (3XLR)
Instructions of Buttons

Set up DMX address

When the digital LED is not flashing, press "A", digital LED begin to flash, press "A" once, active digital LEDs move backwards, you can start to edit the second digital LED: Press "B", the corresponding flash digital LED increase one bit (the values between 0 to 9), see the following diagram:
Range of valid address: 001-512

Adjustment and selection of function for independent mode

After pressing "A" four times (the first three times is the setup on DMX address), light enter into independent mode: the digital LEDs show PXY, press A once, active digital LEDs move backward, you can choose function via X and parameter via Y: Press "B", the corresponding flash digital LED increases one bit (the values between 0 to 9), see the following diagram:

"X" corresponds to the choice of function (the value is between 1 to 3.). "Y" corresponds to the value of speed and gray degree for some function (the value is between 1 to 9.).

The sheet of functions and parameter:

X Value

Y Value

1-single red

1-9 class gray degree

2-single green

1-9 class gray degree

3-single blue

1-9 class gray degree

4-single yellow

1-9 class gray degree

5-single purple

1-9 class gray degree

6-single cyan

1-9 class gray degree

7-single white

1-9 class gray degree

8-multicolor jumping

1-9 class gray degree

9-multicolor fading

1-9 class gray degree

A-multicolor flashing

1-9 class gray degree

When pressing a button, please wait for about 10 seconds, then you can exit the mode of adjustment function, the digital LED stop flashing and to memorize the selected parameters.

Usage Instructions

1. Independent mode, you can adjust the present functions of light by button on the side cap;
2. DMX mode, DMX console to control the light, referring to the manual of the relevant console for attaining more information;
3. Auto online function for independent mode, please choose at random some lights as master to attain auto online function, the relative operation as below: firstly, set the address of a master as 001, others are be set as a slave. For auto online mode, only one master, all effects depend on the effect of the master;
4. DMX address, each light occupies three DMX channels, which is red, green and blue including the value of the initial channel. For example, light with DMX address 001 occupies the channel 1, 2 and 3, address 256 occupies the channel 256, 257 and 258;

Phone: 86-755-6118-7778 (English Service)    Fax: 86-755-6118-7077
Website:http://www.fobsun.com    Email:sales@fobsun.com
PrintClose